How to Clean Powerlix Milk Frother

To clean the Powerlix milk frother, begin by emptying out any remaining milk from the cup. Rinse it with cold water and wipe down with a damp cloth to remove any residue. Next, fill up the cup with warm water and add one teaspoon of white vinegar and two teaspoons of baking soda.

Place the stem into the mixture and leave for about 10 minutes before turning on the machine. Once your cleaning solution has been running for approximately one minute, turn off your machine, empty out all of your liquid mix and rinse thoroughly with fresh cold water until all traces are gone. Finally, dry off both parts thoroughly before use again!

Fix a PowerLix milk frother

  • Step 1: Unplug the Powerlix Milk Frother from its power source
  • This step is important for safety purposes
  • Make sure that the frother is unplugged before cleaning it to avoid any risk of electric shock as well as damage to the device
  • Step 2: Disassemble all parts of your frother, including the whisk and stand
  • Remove all parts that make up your Powerlix Milk Frother such as its whisk, stand, plunger and lid so they can be separately cleaned
  • Step 3: Rinse each part with warm water and regular dish soap
  • Using a mild dish soap solution, rinse off each part thoroughly with lukewarm water before wiping them dry with a clean cloth or paper towels
  • Do not use abrasive materials or harsh chemicals when cleaning these delicate pieces to avoid damaging them in any way possible
  • Step 4: Submerge the metal shaft in boiling hot water for about 10 minutes
  • Fill a pot or container large enough to fit in all parts of your Powerlix Milk Frother with boiling hot water and submerge its metal shaft into it for approximately 10 minutes then remove it from heat source once done soaking
  • This should help loosen up any built-up residue on this component which will aid you in easily removing them during cleaning process later on down line
  • Step 5: Use an old toothbrush dipped in rubbing alcohol to brush away leftover residue
  • Using an old toothbrush dipped into rubbing alcohol scrub away any remaining residue left behind after soaking previously mentioned metal shaft inside boiling hot water earlier
  • Doing this ensures complete removal of stubborn particles without having worry about causing potential damages due being too vigorous while trying clean out tough spots manually by hand
How to Clean Powerlix Milk Frother


How Do You Clean the Inside of a Milk Frother?

To clean the inside of a milk frother, start by filling it with warm water and some dish soap or mild detergent. Allow this mixture to sit in the frother for at least 10 minutes before rinsing out with cold water. For tough stains, use a soft cloth or soft-bristled brush to remove any residue from inside the unit.

Once you are satisfied that all of the debris has been removed, rinse again with cold water and let air dry. If your machine is equipped with an auto-clean function, refer to manufacturer instructions on how best to use it. Additionally, regularly descaling your appliance will help ensure optimal performance and extend its life span significantly.

How Do You Get Burnt Milk Out of a Milk Frother?

The best way to get burnt milk out of a milk frother is to first unplug the appliance and allow it to cool down. Once cooled, empty any remaining liquid from the jug and fill it with one part water and two parts white vinegar. Securely place the lid onto the jug and set your machine’s dials so that it will heat up but not steam.

Run this mixture through your appliance for about 30 seconds before turning it off again. Finally, rinse out the jug with fresh water several times until all traces of burned milk have been removed from inside the device.

How Do You Fix a Milk Frother That Won’T Froth?

If your milk frother is no longer producing the delicious foam for your morning coffee, there are a few steps you can take to try and fix it. First, ensure that the frothing wand or coil is immersed in liquid when you turn it on, as this will help create air bubbles necessary for foaming. You may also need to clean the frother if it has been used for a long time without being cleaned and descaled; use white vinegar or an appropriate cleaning solution specifically designed for milk frothers and follow manufacturer’s instructions carefully.

If these tips still don’t work then you may need to replace some of the parts of the machine such as gaskets, seals or O-rings which tend to wear out over time due to friction.


In conclusion, cleaning your Powerlix Milk Frother is an important part of its maintenance. It’s recommended to rinse and dry the metal whisk after each use and give it a more thorough clean every few weeks with a brush or mild detergent. By following these steps, you can be sure that your frother will look like new and perform perfectly for many years to come!


Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top